RH-01 / HALLWAY REMOTE HOLSTER 14 OCT 2026
Quieter.
Not fancier.
v0.3 settled function on the wall: it covers the old switch plate, catches both nubs and keeps the lower nub off the remote. This note is the form pass that followed: what the repo's form rules allow, the six moves Daniel agreed, three finishes to choose from, and the v0.4 CAD built from them.
01 / v0.4
The v0.4 holster, as modelled.
All six moves plus a 2 mm seat correction from the v0.3 fit. Drag to orbit, scroll or pinch to zoom. Ghost shows the nub cavities hidden behind the closed front.
Actual v0.4 mesh · 68.4 × 119 × 25.5 mm
Keyboard: focus the 3D view, use arrow keys to pan, Shift + arrows to orbit, + or − to zoom, and 0 to reset.
02 / THE RULES
What the repo already decided.
None of this is new taste. Each rule was written after a design went wrong, and each one names the mistake it prevents.
Warmth comes from proportion and considered radii, never from added detail. A feature that holds, guides or stiffens stays. Anything else goes.
proportional-form-system §6–7Pick one base dimension and halve it for every radius. A radius chosen by feel is the symptom the system exists to kill.
proportional-form-system §3The fewest crisp primitives, not a melted loft. Both early A/B candidates became organic blobs and were rejected. A clean sharp edge can be the resolved answer.
proportional-form-system §10Only the bed edge, where it also fixes elephant's foot. Daniel called the opposite "chamferiosis" on grid_platform.
memory: chamfers-earn-their-placeRound-overs face up in the print. Matte filament and a scarf seam beat modelling for finish. Ironing leaves a glossy patch on matte PLA.
surface-finish-is-an-architecture-decisionThe house language is Teenage Engineering: flat, crisp, one strong accent that signals a function. Text on parts uses the monospace register.
DESIGN.md03 / THE MOVES
Six changes, each checked against a rule.
Daniel agreed these from the brainstorm. Two carry a constraint the photos can hide.
| MOVE | WHAT CHANGES | RULE AND CONSTRAINT |
|---|---|---|
| Soft silhouette | Radius family from the remote's 32.7 mm width: about 8 mm on the cover corners, 4 mm on the wall tops, 2 mm on the lip edges. | One radius family. The rounds face up in the print, so they come out clean. |
| Angled wall tops | The pocket wall ends cut at a crisp 45° instead of square. | The pocket depth itself can't taper: the remote is 14.8 mm thick from end to end. A cupped, curved wall would break "warmth is not swoop". |
| Closed front | A cover about 6.5 mm thick, with the nub heads in hidden pockets behind a solid face. No keyholes visible from the room. | The thick cover holds the remote clear of the 4.6 mm nub on its own, so the rails can go: one feature fewer. The pocket roofs need a gable so they print without support. |
| Shadow gap | A 45° chamfer on the back edge all round, so the slab seems to float off the wall. | The one chamfer the repo approves of: it is the bed edge, and it fixes elephant's foot. |
| Surface | Matte PLA, as now, plus a scarf seam. | The scarf needs two switches in Bambu Studio. It gets checked in the sliced file, not assumed. No ironing. |
| Thumb scoop | A curved ramp cut across the front of the pocket floor, replacing the round notch. | One continuous surface where the cut meets the face, not a box subtracted into the body. |
04 / DIRECTIONS
Same geometry, three finishes.
Generated concept photos on the real hallway wall. They show intent, not dimensions. Pick one, then the v0.4 CAD is built from the contract.





Where the concepts lie. The wall tops read as square with soft corners, not the 45° cut. The thumb scoop still looks like the old U-notch rather than a curved ramp. The back-edge shadow chamfer is barely visible. The remote stands a little higher above the walls than the planned 8 mm. The CAD follows the table above, not these pixels.
05 / EVIDENCE & NEXT
Function first, then form.
The repo resolves safety, then function, then interfaces, then form. v0.3 settled function on the wall. v0.4 carries the form pass and the fit correction, and has not been printed.
- v0.3
- Printed on the H2C and fitted 14 October 2026: "much better fit". It sat 2 mm low, which v0.4 corrects.
- v0.4
- Sealed CLEAN with four geometry gates: both keyholes, an 8 mm cavity-roof bridge, a closed front skin, the pocket and the scoop. Print, fit and form call are open.
- Concepts
- Three Codex image generations from one prompt, stored with the design. Visual intent only; no number comes from them.
- Open
- Daniel's choice of A, B or C, the v0.4 print with a scarf seam checked in the slice, and the form verdict.
Files
v0.4 holster STL ↓v0.3 true-scale views PNG ↗v0.2 on the wall JPG ↗The STL is the sealed v0.4 export from the design folder. The true-scale views are from v0.3.